ninja =p

Senin, 23 Juli 2012

ACL 1

ROUTER 0


Router>ena

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router (config)#int fa0/0

Router (config-if)#ip add 172.16.10.1 255.255.255.0

Router (config-if)#no shut



Route (config-if)#exit

Router(config)#int fa1/0

Router (config-if)#ip add 172.16.20.1 255.255.255.0

Router(config-if)#no shut



Router(config-if)#exit

Router(config)#int se2/0

Router(config-if)#ip add 172.16.30.1 255.255.255.0

Router(config-if)#no shut


%LINK-5-CHANGED: Interface Serial2/0, changed state to down

Router(config-if)#exit

Router(config)#router eigrp 10

Router(config-router)#network 172.16.10.0 0.0.0.255

Router(config-router)#network 172.16.20.0 0.0.0.255

Router(config-router)#network 172.16.30.0 0.0.0.255

Router(config-router)#exit

Router(config)#exit





ROUTER 1


Router>ena

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#int fa0/0

Router(config-if)#ip add 172.16.40.1 255.255.255.0

Router(config-if)#no shut


%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up


%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up


Router(config-if)#exit

Router(config)#int fa1/0

Router(config-if)#ip add 172.16.50.1 255.255.255.0

Router(config-if)#no shut


%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up


%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up


Router(config-if)#exit

Router(config)#int se2/0

Router(config-if)#ip add 172.16.30.2 255.255.255.0

Router(config-if)#clock rate 64000

Router(config-if)#no shut


%LINK-5-CHANGED: Interface Serial2/0, changed state to up


Router(config-if)#exit

Router(config)#int se3/0

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config-if)#ip add 172.16.60.1 255.255.255.0

Router(config-if)#clock rate 64000

Router(config-if)#no shut


%LINK-5-CHANGED: Interface Serial3/0, changed state to down

Router(config-if)#exit

Router(config)#router eigrp 10

Router(config-router)#network 172.16.40.0 0.0.0.255

Router(config-router)#network 172.16.50.0 0.0.0.255

Router(config-router)#network 172.16.30.0 0.0.0.255

Router(config-router)#

%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 172.16.30.1 (Serial2/0) is up: new adjacency


Router(config-router)#network 172.16.60.0 0.0.0.255

Router(config-router)#exit

Router(config)#exit


%SYS-5-CONFIG_I: Configured from console by console

Router#



Router 2


Router>ena

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#hostname Router

Router(config)#int fa0/0

Router(config-if)#ip add 172.16.70.1 255.255.255.0

Router(config-if)#no shut


%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up


%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up


Router(config-if)#exit

Router(config)#int fa1/0

Router(config-if)#ip add 172.16.80.1 255.255.255.0

Router(config-if)#no shut


%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up


%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up


Router(config-if)#exit

Router(config)#int se2/0

Router(config-if)#ip add 172.16.60.2 255.255.255.0

Router(config-if)#no shut


%LINK-5-CHANGED: Interface Serial2/0, changed state to up


Router(config-if)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up


Router(config-if)#exit

Router(config)#router eigrp 10

Router(config-router)#network 172.16.70.0 0.0.0.255

Router(config-router)#network 172.16.80.0 0.0.0.255

Router(config-router)#network 172.16.60.0 0.0.0.255

Router(config-router)#

%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 172.16.60.1 (Serial2/0) is up: new adjacency

Router(config-router)#exit

Router(config)#exit




 Setting ACL :


1. Network 10.0 tidak boleh di akses oleh network 40.0


Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#access-list 10 deny 172.16.40.0 0.0.0.255

Router(config)#access-list 10 permit any

Router(config)#int fa0/0

Router(config-if)#ip access-group 10 out

Router(config-if)#end




2. Network 10.7 tidak boleh di akses oleh network 10.5


Router#ena

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#access-list 110 deny ip host 172.16.10.5 host 172.16.50.7

Router(config)#access-list 110 permit ip any any

Router(config)#int fa1/0

Router(config-if)#ip access-group 110 out

Router(config-if)#end




3. Network 10.5 boleh mengakses Router 1 meggunakan telnel

Router#ena

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#access-list 20 permit host 172.16.10.5

Router(config)#line vty 0 4

Router(config-line)#access-class 20 in

Router(config-line)#end


 

 
Diposting oleh di Tidak ada komentar:

Rabu, 13 Juni 2012

KONFIGURASI EIGRP

Rabu, 13 Juni 2012

Konfigurasi EIGRP

 Gambar : Hasil Akhir
Setting ROUTER 0


Router>ena

Router#conf t

Router(config)#int fa0/0

Router(config-if)#ip add 172.16.10.1 255.255.255.0

Router(config-if)#no shut

Router(config-if)#exit

Router(config)#int s2/0

Router(config-if)#ip add 172.16.20.1 255.255.255.0

Router(config-if)#no shut

Router(config-if)#exit

Router(config)# router eigrp 10

Router(config-router)#net 172.16.0.0 0.0.0.255

Router(config-router)#net 172.16.10.0 0.0.0.255

Router(config-router)#net 172.16.20.0 0.0.0.255

Router(config-router)#net 172.16.30.0 0.0.0.255





Setting ROUTER 1


Router>ena

Router#conf t

Router(config)#int fa0/0

Router(config-if)#ip add 172.16.30.1 255.255.255.0

Router(config-if)#no shut

Router(config-if)#exit

Router(config)#int s2/0

Router(config-if)#ip add 172.16.20.2 255.255.255.0

 Router(config-if)#clock rate 64000

Router(config-if)#no shut

Router(config-if)#exit

Router(config)# router eigrp 10

Router(config-router)#net 172.16.0.0 0.0.0.255

Router(config-router)#net 172.16.10.0 0.0.0.255

Router(config-router)#net 172.16.20.0 0.0.0.255

Router(config-router)#net 172.16.30.0 0.0.0.255 




Setting LAPTOP 0

IP         : 172.16.10.10

SM       : 255.255.255.0

GW      : 172.16.10.1



Setting LAPTOP 1

IP         : 172.16.30.30

SM       : 255.255.255.0

GW      : 172.16.30.1
 Gambar. Table Routing0

Gambar. Table Routing1


 Gambar. Tampilan pengujian melalui Laptop0


Gambar. Tampilan pengujian melalui Laptop1
Diposting oleh di Tidak ada komentar:

Selasa, 29 Mei 2012

KONFIGURASI DENGAN ROUTER STATIC



     ROUTER1
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.3.1 255.255.255.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 172.16.2.1 255.255.255.0   
Router(config-if)#clock rate 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#ip route 172.16.0.0 255.255.252.0
% Incomplete command.
Router(config)#ip route 0.0.0.0 0.0.0.0 ser2/0
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

    ROUTER2
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.1.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 172.16.2.2 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#int ser
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up 3/0
Router(config-if)#int ser3/0
Router(config-if)#ip add 192.168.1.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit
Router(config)#ip route 172.16.0.0 255.255.252.0 ser2/0
Router(config)#ip route 192.168.2.0 255.255.255.0 192.168.1.1
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#
%LINK-5-CHANGED: Interface Serial3/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up

        ROUTER3
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.2.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser3/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface Serial3/0, changed state to up
Router(config-if)#exit
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to upip route
% Incomplete command.
Router(config)#ip route 0.0.0.0 0.0.0.0 ser3/0
Router(config)#ip route 172.16.1.0 255.255.255.0 192.168.1.2
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console

PC0
IP ADD : 172.16.3.3
SM : 255.255.255.0
DG : 172.16.3.1
PC1
IP ADD : 172.16.1.3
SM : 255.255.255.0
DG : 172.16.1.1
PC2
IP ADD : 192.168.2.3
SM : 255.255.255.0
DG : 172.16.2.1






 







 


Diposting oleh di Tidak ada komentar:
Langganan: Postingan (Atom)