ROUTER 0
Router>ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router (config)#int fa0/0
Router (config-if)#ip add 172.16.10.1 255.255.255.0
Router (config-if)#no shut
Route (config-if)#exit
Router(config)#int fa1/0
Router (config-if)#ip add 172.16.20.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 172.16.30.1 255.255.255.0
Router(config-if)#no shut
%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#router eigrp 10
Router(config-router)#network 172.16.10.0 0.0.0.255
Router(config-router)#network 172.16.20.0 0.0.0.255
Router(config-router)#network 172.16.30.0 0.0.0.255
Router(config-router)#exit
Router(config)#exit
ROUTER 1
Router>ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.40.1 255.255.255.0
Router(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int fa1/0
Router(config-if)#ip add 172.16.50.1 255.255.255.0
Router(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 172.16.30.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#exit
Router(config)#int se3/0
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up
Router(config-if)#ip add 172.16.60.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut
%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit
Router(config)#router eigrp 10
Router(config-router)#network 172.16.40.0 0.0.0.255
Router(config-router)#network 172.16.50.0 0.0.0.255
Router(config-router)#network 172.16.30.0 0.0.0.255
Router(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 172.16.30.1 (Serial2/0) is up: new adjacency
Router(config-router)#network 172.16.60.0 0.0.0.255
Router(config-router)#exit
Router(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Router#
Router 2
Router>ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname Router
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.70.1 255.255.255.0
Router(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int fa1/0
Router(config-if)#ip add 172.16.80.1 255.255.255.0
Router(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 172.16.60.2 255.255.255.0
Router(config-if)#no shut
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up
Router(config-if)#exit
Router(config)#router eigrp 10
Router(config-router)#network 172.16.70.0 0.0.0.255
Router(config-router)#network 172.16.80.0 0.0.0.255
Router(config-router)#network 172.16.60.0 0.0.0.255
Router(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 172.16.60.1 (Serial2/0) is up: new adjacency
Router(config-router)#exit
Router(config)#exit
Setting ACL :
1. Network 10.0 tidak boleh di akses oleh network 40.0
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#access-list 10 deny 172.16.40.0 0.0.0.255
Router(config)#access-list 10 permit any
Router(config)#int fa0/0
Router(config-if)#ip access-group 10 out
Router(config-if)#end
2. Network 10.7 tidak boleh di akses oleh network 10.5
Router#ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#access-list 110 deny ip host 172.16.10.5 host 172.16.50.7
Router(config)#access-list 110 permit ip any any
Router(config)#int fa1/0
Router(config-if)#ip access-group 110 out
Router(config-if)#end
3. Network 10.5 boleh mengakses Router 1 meggunakan telnel
Router#ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#access-list 20 permit host 172.16.10.5
Router(config)#line vty 0 4
Router(config-line)#access-class 20 in
Router(config-line)#end
